Stanley 1/4" & 3/8" Drive Socket Set - 41 Piece
Before you begin installing a remote garage door opener, raise and lower the door to make sure it is correctly balanced and rolls freely. Remove any locks or ropes that might hinder it. Also, lift the door to about halfway and release it. The door should remain perfectly balanced. If there are problems, call a roller door technician to get it repaired before installing the opener.
You need to install the stop collar on the opposite end to the motor. Fit the stop collar hard against the boss of the door drum. Make sure the U-bolt holding the door shaft is tightly fastened. If it isn't, the spring tension won't work and the door won't function.
The weight bar needs to be installed in the centre at the bottom of the door. If your door doesn't have a handle, drill two 5.5mm holes through the two marked positions and place the weight bar on the inside of the door. Use the bolts, washers, and nuts to fasten the weight bar in place. If your door has a lifting handle, remove it and install the weight bar in this spot.
Thread one end of the rope through the hole in the top of the red release handle. Secure with an overhead knot at least 25mm from the end of the rope, this will prevent slipping. Thread the other end of the rope through the loop of the manual release cable. Adjust the length so the handle is no higher than 1.8m above the floor. Secure with an overhead knot.
Disengage the opener by pulling on the release cable. You will know the motor is disengaged when you hear an audible click. The release cable allows you to open and close the door manually if there's a blackout or you've lost the remote.
To make sure the roller door is secure before you install the motor, pin it to the drum with screws. It's important to do this so that your door doesn't balloon, which may delay the safety reversal response and compromise security. To do this, close the roller door and mark the last part of the curtain where it meets the drum. This is where the screws should go.
Roll up the door until the mark is visible. Then lift the door about half a turn from the closed position to give you enough room to drill. Secure the screws through the door curtain and into the drum wheel at the end of each roll. Now the door is pinned, you can install the motor.
The motor can be installed on either the right- or left-hand side of the door, but it needs to be opposite the stop collar. Place the opener in manual release mode, and open the door fully. Make sure the U-bolt on the other side is tight. Before removing a heavy roller door from its bracket, get a friend to help by supporting the door. You'll also need a ladder and a ratchet tie-down strap or rope for extra support. Once the door is supported, mark the position of the door shaft on the right hand door bracket.
Once the roller door is supported you can remove the right hand axle U-bolt and mounting bracket from the wall.
Install the motor by sliding the opener over the axle and then engage the drive legs into the door drum wheel either side of the spoke.
Refit the door mounting bracket to the wall. Clamp the opener to the axle and bracket using the clamp that's supplied. Then you can remove all the ropes and the support ladder.
Check the operation of the roller door by disengaging the motor and manually rolling the door up and down.
Make sure the door is halfway and the opener is engaged. Plug the opener into the power supply, the LED lights should come on. Now it's time to program the opener. You can program it for left and right operation, door travel limits and force limits. To program your garage opener, refer to the instruction manual included in your roller door pack.
To check the safety reverse system is working, place a block of wood or another object under the roller door. Close the door. You will know it works if the roller door touches the object and automatically reverses.
Attach the warning labels to the garage wall.
Asbestos, lead-based paints and copper chromium arsenic (CCA) treated timber are health hazards you need to look out for when renovating older homes. These substances can easily be disturbed when renovating and exposure to them can cause a range of life-threatening diseases and conditions including cancer. For information on the dangers of asbestos, lead-based paint and CCA treated timber and tips for dealing with these materials contact your local council's Environmental Health Officer or visit our Health & Safety page.
When following our advice in our D.I.Y. videos, make sure you use all equipment, including PPE, safely by following the manufacturer’s instructions. Check that the equipment is suitable for the task and that PPE fits properly. If you are unsure, hire an expert to do the job or talk to a Bunnings Team Member.