Project Overview

Tiles are a great way to bring colour and style to a bathroom renovation. If you can do the tiling yourself, the whole project will be a lot more affordable. We’ll teach you how to lay your tiles in neatly spaced rows. You will also learn how to trim around window gaps and keep your rows horizontal.

Continue to step-by-step instructions
This D.I.Y. Advice is part of a series How To Lay Wall Tiles

Step by Step Instructions

1 Draw a datum line one row above the bathroom floor
2 Install a temporary timber shelf on the datum line
3 Check your tile glue is safe to use with waterproofing
4 Find out the width of the last tile in a row
5 Mix up the tile glue
6 Lay the first row of tiles
7 Level up the first row of tiles
8 Lay more rows of tiles on the bathroom wall
9 Trim and lay edge and corner tiles
  • Step 1. Draw a datum line one row above the bathroom floor

    Measure your tile height, and mark a point on the bathroom wall that is 20mm below that height. Then use your spirit level to draw a horizontal line, known as a “datum line”, at that height all the way around the room. The height is reduced by 20mm just in case there is a low point in the floor that needs covering.
  • Step 2. Install a temporary timber shelf on the datum line

    Get a long, straight piece of timber and mount it on the bathroom wall so its top edge lines up with your datum line. Then drive a screw through the middle of the timber into a wall stud. Now use a spirit level to check the timber is horizontal and screw the two ends into wall studs as well.
  • Step 3. Check your tile glue is safe to use with waterproofing

    Building regulations require the walls of your bathroom to have a waterproof lining installed. Once that lining is in place, you can start tiling. Check the information on the side of your packet of tile glue to make sure that it is safe to use with waterproofing. 
  • Step 4. Find out the width of the last tile in a row

    To work out the width of the last tile in a row, lay one tile in position on the timber shelf you have installed. Then move it down the shelf one tile-width at a time, plus the width of a spacer, until you reach the end of the row. If the final tile needs to be short, you can pre-trim one for each row before you start tiling.
  • Step 5. Mix up the tile glue

    Pour some tile glue powder into a bucket with some water in it, then use a power drill with a mixing paddle to blend the mixture together. Keep mixing until the glue has the consistency of toothpaste. If you find that it’s too runny or dry, then balance it out with a little more powder or water.
  • Step 6. Lay the first row of tiles

    Spread some glue on the back of the first tile using the notched edge of your trowel. This makes trenches in the glue so the tile sticks better. Then place the base of the tile on the timber shelf and flatten it onto the wall. Clean off any excess glue and push plastic wedges under the bottom corners of the tiles. Repeat for every tile across the row, putting spacers between each tile as you go.
  • Step 7. Level up the first row of tiles

    Once the first row of tiles has been laid, put a spirit level on top to check that they are horizontal. This is where the wedges are helpful. If any of the tiles need adjusting, simply shift the position of the wedges to lift or drop the tiles so they line up correctly.
  • Step 8. Lay more rows of tiles on the bathroom wall

    Put enough glue on the wall to cover a couple of rows of tiles. Once again, use the notched side of your trowel to put trenches in the glue as you spread it. When you have spread the glue, work quickly to put your tiles in place before the glue starts to cure. Lay them one row at a time, using plastic spacers to keep the gaps between each tile the same. If you need to trim a tile before you lay it, leave that area free of glue and do that tile as part of the next step.
  • Step 9. Trim and lay edge and corner tiles

    When you need to trim a tile before you lay it, put the tile in place on the wall, mark your cutting points and use a tile cutter or angle grinder to trim the tile to size. Then put your tile in place again to check the cut is right, put some glue on the back and lay it in position. For more information on cutting tiles, check out our How to cut tiles video.

Tools and Materials

Tools

  • Angle grinder
  • Buckets
  • Drill
  • Dust mask
  • Ear muffs
  • Hammer
  • Marker pen
  • Measuring tape
  • Mixing paddle
  • Notch trowel
  • Paint scraper
  • Pencil
  • Rags
  • Safety glasses
  • Spirit level
  • Tile cutter
  • Timber strip

Materials

  • Mastic glue
  • Tile separators
  • Tile wedges
  • Tiles
Rug 01:13

Flooring Ideas How to choose the right rug for any room A rug can add warmth, personality and really affect the look and feel of a room. The trick to finding the right rug for any room comes down to three things: size, colour and material.

tiled bathroom

Flooring Ideas How to choose the right type of flooring With so many different types of flooring available, choosing the right type for your home is not easy. Whether your priority is function or style, there's a flooring option to suit every room in your home.

Floor covering material 01:13

Flooring Ideas How to choose floor coverings for a beach house Choosing the right floor covering for a beach house is important. Find out the best floor coverings and how to clean them.

How to lay laminate flooring 05:32

Laminate & Vinyl How to lay laminate flooring Laying a laminate floor can be a relatively cheap, quick and easy way to update a room in your home. It’s relatively easy to do yourself and we’ll show you how.

0225RemoveLino09summary 04:06

Laminate & Vinyl How to remove vinyl floor An inexpensive way to help give an old room a facelift.

Dry lay the tiles before applying adhesive 04:49

Tiles How to lay floor tiles Tiles are a great way to bring colour and style to a room. We’ll show you how easy it is to lay floor tiles with this easy to follow guide.

Scrape grout with removing tool 05:28

Tiles How to replace a broken floor tile A broken floor tile in your kitchen or bathroom can be a real eyesore and potentially dangerous. Learn how easy it is to you can replace a tile yourself.

Woman installing chipboard floor panel 03:56

Subfloor How to lay chipboard flooring Tongue and groove chipboard flooring is a common building material. Learn how quick it is to install yourself.

Health & Safety

Please make sure you use all equipment appropriately and safely when following the advice in these D.I.Y. videos. You need to be familiar with how to use equipment safely and follow the instructions that came with the equipment. If you are unsure, you may feel it is safest to consult an expert, such as the manufacturer or an expert Bunnings Team Member.

Grave health hazards are linked to asbestos, which may be in homes built up to 1990. Health hazards may result from exposure to lead-based paints in older materials and copper chromium arsenic (CCA) treated timber. For information on the dangers of asbestos, lead-based paint and CCA treated timber and tips for dealing with these materials contact your local council's Environmental Health Officer or visit our Health & Safety page. You can also use a simple test kit from Bunnings to indicate the presence of lead-based paint.
Top of the content