Project Overview

Attract more birds to your backyard with this bird feeder. It’s easy and affordable, and looks great hanging from a tree. Plus, you can get to know the birds that live in your area and help them out with a snack when they’re feeling a bit peckish.

Continue to step-by-step instructions
clogged paint spray
View the video

How to unclog a spray can

Occasionally the nozzle on a used can of spray paint can get clogged and stop working. A quick and easy solution is to pour a small amount of mineral turpentine into a bucket, then remove the nozzle from the top of the can and place it in the bucket. After about three minutes, remove the nozzle, dry it off and reattach it to the spray can. Shake the can well then give it a spray, with the blockage gone your paint should come out no problem at all.

Step by Step Instructions

1 Cut the timber
2 Measure and mark the base tray
3 Cut the base tray
4 Measure, mark and cut the base piece
5 Sand the timber
6 Secure the frame
7 Insert the base into the frame
8 Drill drainage holes
9 Drill the holes for the centre panel
10 Measure and mark for the centre panel
11 Cut the centre panel
12 Make the roof panel
13 Trace around the stencil
14 Drill holes in the centre panel
15 Cut out the bird
16 Pre-drill holes in the roof
17 Attach the centre panel to the base
18 Drill a hole for the eyelet
19 Attach the roof
20 Paint the bird feeder
21 Attach the eyelet to the bird feeder
22 Drill holes for a skewer
23 Time to attract the birds
  • Step 1. Cut the timber

    To make this job easier, you can get your timber cut to size at your local Bunnings Warehouse.

    Cut the 1200mm x 596mm ply to the following lengths:

    • 180mm x 300mm (roof)
    • 230mm x 340mm (centre panel)

    Cut the 42mm x 19mm Tasmanian oak to the following lengths:

    • 92mm x 2 (tray ends)
    • 290mm x 2 (tray sides)

    Cut the 92mm x 19mm Tasmanian Oak to the following length:

    • 252mm x 1 (tray base)
  • Step 2. Measure and mark the base tray

    The base tray is made from Tasmanian oak hardwood, but you can use any hardwood you like. Measure and mark the timber. Our base tray measured 92mm x 2 for the tray ends and 290mm x 2 for the longer sides.

  • Step 3. Cut the base tray

    Use the drop saw to cut the timber for the base tray to size.

  • Step 4. Measure, mark and cut the base piece

    Then measure, mark and cut the base piece for the tray. Ours measured 252mmx 92mm.

  • Step 5. Sand the timber

    Lightly sand all of the cut timber to remove any sharp edges.
  • Step 6. Secure the frame

    Once the sides and base are cut, lay out the tray. Ensure the corners are square before securing with a fixing gun.

  • Step 7. Insert the base into the frame

    Place the base inside the frame, it should fit snugly. Then, secure the base with the nail gun.

  • Step 8. Drill drainage holes

    Once the tray is finished, measure and mark for the drainage holes in the base of the tray. We put four on each side of the tray. Use a 5.5mm drill bit to make the holes.

  • Step 9. Drill the holes for the centre panel

    Measure and mark for the holes in the centre of the base, so you can attach the centre panel. Use the 5.5mm drill bit to pre-drill the holes. Be sure to take into account the width of the centre panel timber.

  • Step 10. Measure and mark for the centre panel

    Now it’s time to cut the centre panel to size. Firstly, cut a straight edge on the timber with the saw. Then, measure and mark out the size of your panel. Ours measured: 230mm x 340mm.

  • Step 11. Cut the centre panel

    Use the drop saw to cut the panel to the correct length. Then measure, mark and cut for the width. Once the straight cuts are completed, set up the drop saw to a 10-degree mitre cut for the top of the centre panel. This angle will allow for rain water run-off.

  • Step 12. Make the roof panel

    Now, measure, mark and cut the roof piece. Our roof measured 180mm x 300mm. 

  • Step 13. Trace around the stencil

    You can get a template for the centre panel from the Bunnings website or you can create your own. Once you’ve got your template, make a stencil, from cardboard, and transfer it onto the centre panel. Position the stencil on the centre panel wherever you like. Ours was centred. Trace around the stencil with a pencil.  Be sure the stencil is the right way up – the head of the bird needs to be closest to the mitre cut that’s the top of the centre panel.

  • Step 14. Drill holes in the centre panel

    Clamp the panel to the workbench. Use the 5.5mm drill bit to drill holes in the tighter corners around the picture on the panel. These holes ensure the jigsaw gets into the tight spots on the bird and also help to create a more accurate shape. Use as many drill holes as necessary, and use different size drill bits if necessary.

  • Step 15. Cut out the bird

    Use the jigsaw to cut out the bird shape in the centre panel. Sand off any rough edges. You can wrap a piece of sandpaper around a drill bit to sand in the corners and the feet.

  • Step 16. Pre-drill holes in the roof

    Measure, mark and pre-drill two pilot holes (with the 5mm bit) in the roof to attach the centre panel. These holes should be on an angle.

  • Step 17. Attach the centre panel to the base

    Place the centre panel in the middle of the base tray. Screw it into place with the 50mm screws. Make sure the centre panel is square, before screwing it firmly into place.

  • Step 18. Drill a hole for the eyelet

    Find the centre of the roof panel. The easy way to do this is by drawing diagonal lines from corner to corner. Use the 5mm bit to pre-drill a hole for the eyelet.

  • Step 19. Attach the roof

    Place the roof panel evenly on top of the centre panel. Secure the roof to the centre panel with 50mm screws.

  • Step 20. Paint the bird feeder

    Once assembled, fill the screw holes with putty, allow to dry before sanding and painting. Apply as many coats as necessary for good coverage. Allow to dry between coats and lightly sand with 120 grit sandpaper between coats. 

  • Step 21. Attach the eyelet to the bird feeder

    Screw an eyelet into the pre-drilled hole in the roof. Use the pliers to open a link on the chain, thread it through the eyelet and close the link off again.

  • Step 22. Drill holes for a skewer

    As an added feature we’ve drilled a hole in each side of the bird feeder to put a skewer through. The birds will love feeding on fruit threaded on the skewer.

  • Step 23. Time to attract the birds

    Now your feeder is finished it’s time to hang it in your favourite tree, sit back and watch the local birdlife enjoy the fruits of your labour.

Tools and Materials


  • Combination square
  • Compound mitre saw
  • Cordless drill
  • 5.5mm drill bit
  • 5mm drill bit
  • Dust mask
  • Earmuffs
  • Fixing gun and brads
  • Impact driver
  • Jigsaw
  • Multi grips
  • Measuring tape or ruler
  • Paint brush
  • Pencil
  • Pliers
  • Quick clamps
  • Safety glasses
  • Stirrer
  • Tin opener
  • Utility knife
  • Work gloves


  • 90mm x 18mm x 1.8 Tasmanian oak
  • 42mm x 19mm x 1.8m Tasmanian oak
  • 1200mm x 596mm x 18mm plywood
  • 8g 50mm timber screws
  • 33cm BBQ skewers
  • Bird template
  • Chain
  • Disposable gloves
  • Eyelets
  • Paint
  • Rags
  • Sanding block
  • 180 grit sandpaper
  • Tape
  • Wood filler/putty
low water garden

Planning & Projects How to create a low-water garden ‘Dry’ or ‘low-water’ gardening is a real art and, when done right, will provide you with an inviting landscape that uses very little water.

Finished artificial green garden wall behind garden bench 02:05

Planning & Projects How to create a green wall using artificial hedge Green walls are all the rage at the moment, but buying and maintaining one can be costly. Why not have a go at creating your own using pieces of artificial hedge – it looks great and will last the distance. Here’s how.

reducing water

How To Save Water How to reduce water usage Whether indoor or outdoor, there are lots of ways to be smart about water usage. And there are some simple actions that can make a big difference to your water bill.

ring doorbell 01:53

Doors How to install a ring doorbell The Ring video doorbell is a wireless doorbell which allows you to see who is at your front door. Find out how to install the Ring video doorbell yourself.

a tree lit up with solar lights around it 01:46

Garden Lighting How to install solar lights in your garden Solar lights are a great way to illuminate your pathways and highlight your garden beds at night. Install them yourself with these easy steps.

how to organise your pantry 02:52

Shelving & Storage How to organise your pantry Create an organisational system in your pantry with these handy storage hints. Trust us – its life changing!

front door 01:31

How To Paint How to paint your front door Make an entrance every darn day of the week by painting your front door a bold, enticing colour!

how to hang pictures

Walls The best way to hang pictures on a wall Learn the tricks to hanging your wall decor so it looks good – and doesn’t damage the plasterboard. Create an effortless-looking display by taking the time to consider spacing, proportion, frame styles and colour palettes.

Health & Safety

Please make sure you use all equipment appropriately and safely when following the advice in these D.I.Y. videos. You need to be familiar with how to use equipment safely and follow the instructions that came with the equipment. If you are unsure, you may feel it is safest to consult an expert, such as the manufacturer or an expert Bunnings Team Member.

Grave health hazards are linked to asbestos, which may be in homes built up to 1990. Health hazards may result from exposure to lead-based paints in older materials and copper chromium arsenic (CCA) treated timber. For information on the dangers of asbestos, lead-based paint and CCA treated timber and tips for dealing with these materials contact your local council's Environmental Health Officer or visit our Health & Safety page. You can also use a simple test kit from Bunnings to indicate the presence of lead-based paint.
Top of the content