Refresh and renew your timber deck

Even decks that have been carefully maintained deteriorate eventually. As long as the damage is not too extensive, all you may need is a localised fix here and there, restoring it to optimum condition in no time.

Bunnings magazine, October 2019

Replace damaged boards

The most visible problems are often associated with the decking boards. Cracks, rot and splintering pose safety hazards, but if only a few boards are affected, they can be replaced without too much drama.

To remove individual boards that are nailed down, use a pry bar to lever them up. If the boards are secured with screws, use a cordless drill or impact driver to remove the fasteners. Choose new boards with the same section size, and cut them to fit the gaps. As you secure the boards to the joists, use a chisel to lever the boards into position for even spacing along their length.

Upgrade the fasteners

Older boards are often nailed down and, over time, the nails might start to work loose. Lift the boards, remove the nails using a pry bar, then replace with heavy-gauge screws that will grip the joists securely.

Repair decayed handrails

Rot is a common problem in the mitred joints at the corners of timber handrails. If the mitred ends are badly damaged, the best option is to cut a whole new handrail, then paint it or stain it to match the balusters.

If the joint has only opened up slightly, chisel away the rot until you reach sound timber and apply a treatment such as TWA Woodcare Ecoseal. Fill the area with a two-part polyester filler, such as Turbo Builder’s Bog, sand smooth once it has cured, and then repaint over the top.

Cut a drainage channel

The stirrups holding up the posts of older decks might be sunk directly into concrete. This creates a potential decay risk as rainwater soaks into the concrete, causing deterioration of the posts over time. Use an angle grinder with a diamond blade to cut about 20mm clearance around the stirrup, then use a cold chisel to remove the concrete around the base of the post.

Use the angle grinder to cut a drainage channel for rainwater to flow away freely instead of pooling around the base of the post.

Safety tip: It's essential that your deck is structurally sound, so check it regularly and if you have any concerns, consult the professionals

Reinforce the joists

While replacing boards or fasteners, you might discover rot in one or more of the joists. As long as the bearers are sound and the damage is not too major, there is no need to demolish your whole deck. “If there is rot all the way through the joist, you will need to remove it and replace it with an identical-size joist,” says Niall McDarby, co-owner of Fresh Decks Sydney. “If the rot is only at the surface and the joist is still structurally sound lower down, you can attach a new joist along the side of it and into the trimmers at each end. This will support the existing joist and provide a solid fixing for the decking boards on top.”

Sand weathered boards

According to Niall, people often wait too long to recoat their deck. “A product like Intergrain Natural Stain should be reapplied after about 12–15 months,” he says. “But sometimes, life gets in the way and it takes three years to get around to the job. Unfortunately, once grey timber starts poking through, you will need to sand the boards back and start again.”

Use an electric sander with coarse-grit paper to strip the boards back to bare timber (you can hire a sander from Bunnings for the task). Be sure to wear full safety gear, including knee pads, a dust mask, hearing protection and goggles or safety glasses. “Finish with a nice, fine grit to close up the fibres before recoating,” says Niall. Then all you need to do is add a fresh lick of stain, and your deck will look good as new!

Clean and recoat your deck

Minimise maintenance hassles by cleaning and recoating your deck annually. Here’s how:

1. Scrub the boards

“Use a deck-cleaning product to prepare the timber for coating by removing dirt, oils, grease and other contaminants,” says Monarch brand ambassador Mark O’Connor. Apply the product with a stiff-bristled brush, scrub the deck thoroughly, leave for 20 minutes, then rinse off with a hose


2. Apply decking oil or stain

“Use a woodcare brush on the first coat to apply the stain to the edges of each decking board,” says Mark. Cut in around the deck and along the gaps between boards. A lambswool applicator can be used for the upper surface of the deck. “Before use, wash the applicator to ensure no loose fibres will end up stuck in the finish,” adds Mark. Allow it to dry fully before applying decking oil or a solvent-based stain.


3. Add a durable finish

Complete the second coat with the lambswool applicator. “I suggest doing an extra third coat as well,” says Mark. “This will ensure the finish you’ve applied looks great for longer.”


Hit the deck

Now you know some quick tips for renewing your deck, check out your local Bunnings to pick up everything you need.

Photo credit: Cabot’s Premium Woodcare Brands.

low water garden

Planning & Projects How to create a low-water garden ‘Dry’ or ‘low-water’ gardening is a real art and, when done right, will provide you with an inviting landscape that uses very little water.

Finished artificial green garden wall behind garden bench 02:05

Planning & Projects How to create a green wall using artificial hedge Green walls are all the rage at the moment, but buying and maintaining one can be costly. Why not have a go at creating your own using pieces of artificial hedge – it looks great and will last the distance. Here’s how.

reducing water

How To Save Water How to reduce water usage Whether indoor or outdoor, there are lots of ways to be smart about water usage. And there are some simple actions that can make a big difference to your water bill.

doorbell 02:04

Doors How to install a ring doorbell The Ring video doorbell is a wireless doorbell which allows you to see who is at your front door. Find out how to install the Ring video doorbell yourself.

a tree lit up with solar lights around it 01:46

Garden Lighting How to install solar lights in your garden Solar lights are a great way to illuminate your pathways and highlight your garden beds at night. Install them yourself with these easy steps.

how to organise your pantry 02:52

Shelving & Storage How to organise your pantry Create an organisational system in your pantry with these handy storage hints. Trust us – its life changing!

front door 01:31

How To Paint How to paint your front door Make an entrance every darn day of the week by painting your front door a bold, enticing colour!

how to hang pictures

Walls The best way to hang pictures on a wall Learn the tricks to hanging your wall decor so it looks good – and doesn’t damage the plasterboard. Create an effortless-looking display by taking the time to consider spacing, proportion, frame styles and colour palettes.

Health & Safety

Please make sure you use all equipment appropriately and safely when following the advice in these D.I.Y. videos. You need to be familiar with how to use equipment safely and follow the instructions that came with the equipment. If you are unsure, you may feel it is safest to consult an expert, such as the manufacturer or an expert Bunnings Team Member.

Grave health hazards are linked to asbestos, which may be in homes built up to 1990. Health hazards may result from exposure to lead-based paints in older materials and copper chromium arsenic (CCA) treated timber. For information on the dangers of asbestos, lead-based paint and CCA treated timber and tips for dealing with these materials contact your local council's Environmental Health Officer or visit our Health & Safety page. You can also use a simple test kit from Bunnings to indicate the presence of lead-based paint.
Top of the content