Tuff Turf 1.8 x Wide Natural Synthetic Turf - Per Lineal Metre

Per Metre

Price correct as at Thu 11 Feb 2016 1:23:08

I/N: 3300169

Not all products available in all stores, contact your nearest store for product information.


Lifelike Synthetic Grass is designed for Australian conditions to suit domestic or commercial applications. It transforms any area into a green, very low maintenance, aesthetically pleasing space.

Our range of synthetic grass has an easy DIY installation, is child and pet safe, long lasting and will look amazing all year round.

  • Premium lifelike lush grass
  • Fine blade grass mimicking traditional grass featuring a curled brown blade
  • Remains green and fabulous everyday of the year
  • No mowing or watering saving time and money
  • Suitable for any landscape applications including pool surrounds, patios, front and back yards
Model Name
Natural Tuff 35
Model Number
Polyethylene Plastic / Polypropylene / Latex
Green / Beige
Installation Guide
Material Safety Data Sheet
Warranty Info

Tuff Turf N Co offer a genuine 7 year product warranty that is valid from the date of purchase against defects in materials, UV degradation and excessive fading. We will repair or replace, as it deems necessary, those materials which exhibit any of these defects.
We also offer our own Tuff Turf N Co installation warranty for jobs that we undertake but DO NOT warrant against installation carried out by others.
We DO NOT warrant against grooming and maintenance damage caused by improper use, animals, neglect, vandalism, floods, lack of maintenance, animal waste, water table or other acts of mother-nature.

Sustainability Info

Tuff Turf N Co is committed to helping the environment and providing sustainable living solutions. Our grasses are 100% recyclable.

Installation Info

Work out the area where the Tuff Turf will go. Usually
there will be a border of some sort like paving,
concrete or timber edging. If the area is not clear,
mark it out with a rope or spray paint. Remove all
loose vegetation and any debris that is in the way.
Dig out the area to a depth of 75–80mm.
If there are any existing sprinklers, ensure that they
are either capped or removed.
Once the area is excavated, use a rake to level it out
to ensure it is smooth and even for the sub-base.

Place and compact approximately 60mm of crushed
rock as sub-base. Lightly sprinkle water over the
crushed rock before compaction so the base
becomes firm. A vibrating plate will produce the
best result. Ensure you have enough fall on the base
to allow for water drainage.
Complete your base works by adding a fine 20mm
layer of crushed stone over the top of your base and
level it out again following the same procedure. This
will give you a more even finish.
After compacting, your base should be
approximately 15mm below the finished height of
your surrounding edging/paving.

Lay out the Tuff Turf and allow it to relax for several
hours. This will remove any creases and allow the
Tuff Turf to better settle. Always run the grass in the
same direction. Remove the ‘salvage’ black strip
from both sides of the grass. Cut the Tuff Turf to fit
your area. Use a sharp utility knife along edges, and
around trees and flower beds. Take your time to
ensure a flawless finish.
TIP: Keep changing your blade as this will make
cutting the Tuff Turf easier.

Pull the two pieces of Tuff Turf together so they are
as close as possible. Make sure they are not touching
or overlapping. There should never be more than
a 5mm gap. Once in place, position a marker at
both ends of where the two pieces join together.
Fold back both sides of your turf and roll out and
centralise Tuff Turf Adhesive Tape between the two
markers. Cut the tape at one end and gently peel off
the foil along the entire length. Gently place both
sides of the Tuff Turf onto the adhesive tape and
continue this process down the entire length of your
join. Walk along the seam several times to ensure it
sticks down securely.

Secure the edges with 100mm or 150mm flat head
nails. Nail as close to the edge as possible and
continue nailing along the edge every 200–300mm.
Make sure you pull the fibre of the grass apart so the
nail goes in smoothly and does not hold the fibre
down. At completion of this step the nails should be

With a power broom or a stiff bristled broom, brush
the blades of turf upwards. This makes it easier to
distribute the sand infill evenly. Gently spread dried
silica sand across the entire area. We recommend
10–15kg of sand per square metre of turf. The sand
should be spread as evenly as possible. For large
areas you may need to hire a sand spreader tool. For
small areas a seed dropper or a shovel work best.
Aim to get the sand in between the blades of grass.
Large volumes of sand in the one area will cause
lumpy grass.

See installation pdf for visual instructions.

Delivery Info

All special orders are delivered to Bunnings warehouses.

Top of the content